Search Results

WS-400-AX-1 Spray Gun Approval

The ANEST IWATA WS-400-AX-1 spray gun complies with regulations for application of coatings. See specifications on this page for a list of areas we serve.

These approvals are subject to conditions of the regional air quality agency. Information about these approvals are available below or call us at 1-800-470-7068 for details. You may also consult with the regional air quality agency in your jurisdiction.

US EPA Approval
WS-400-AX-1 EPA Compliant Letter PDF

Series 2 WS-400 Compliant Spray Gun SCAQMD Letter
WS-400-AX-1 South Coast Approval Letter

WS-400 Compliance Letters
WS-400 Compliant AIUSNOTICE: It has been brought to our attention that some of ANEST IWATA spray guns sold via the internet may not be in compliance (non-compliant) with US environmental laws because they are not manufactured to be used in the US. We would like to remind customers of these laws, rules and approvals as set forth by the Environmental Protection Agency (EPA) and South Coast Air Quality Management District (SCAQMD), both of which requirements must be met to bring North American based ANEST IWATA spray guns into compliance. Read More…Non Compliant Internet Purchases 2016

 

United States of America Environmental Protection Agency (EPA) Environmental Technology Verification (ETV) ETV’s Verification Report
State General Jurisdiction Agency Complies with Rule/Regulation
AZ Arizona Maricopa Country Maricopa Country Air Pollution Control Regulation III, Rule 345, Vehicle and Mobile Equipment Coating
CA Antelope Valley Antelope Valley AVAQMD Rule 1151 (C)(3)(a)(iii)
CA Sacramento Sacramento Metropolitan Air Quality Management District Rule 459
CA San Joaquin San Joaquin Valley Air Pollution Control District Rule 4602 Section 5.6.4
CA Shasta County Shasta County Air Quality Management District Rule 3:25 section c.5.e
CA South Coast Air Quality Management District Rule 1151(d)(7)(A)(iii)
CO Colorado – entire state Colorado Air Quality Control Commission Regulation Nos. 3 and 7
IN Indiana – entire state Indiana Department of Environmental Management Rule 326 IAC 8-10

WS-400 Spray Gun Approval

The ANEST IWATA WS-400 spray gun complies with regulations for application of coatings. See specifications on this page for a list of areas we serve.

These approvals are subject to conditions of the regional air quality agency. Information about these approvals are available below or call us at 1-800-470-7068 for details. You may also consult with the regional air quality agency in your jurisdiction.

US EPA Approval
WS-400LV EPA Compliant Letter PDF

Spray Guns Listing HVLP and Compliant Letter
AIUS EPA Letter PDF

WS-400 Compliant Spray Gun SCAQMD Letter
WS400 SCAQMD Letter PDF

WS-400 Compliance Letters
WS-400 Compliant AIUS

NOTICE: It has been brought to our attention that some of ANEST IWATA spray guns sold via the internet may not be in compliance (non-compliant) with US environmental laws because they are not manufactured to be used in the US. We would like to remind customers of these laws, rules and approvals as set forth by the Environmental Protection Agency (EPA) and South Coast Air Quality Management District (SCAQMD), both of which requirements must be met to bring North American based ANEST IWATA spray guns into compliance. Read More…Non Compliant Internet Purchases 2016

 

United States of America Environmental Protection Agency (EPA) Environmental Technology Verification (ETV) ETV’s Verification Report
State General Jurisdiction Agency Complies with Rule/Regulation
AZ Arizona Maricopa Country Maricopa Country Air Pollution Control Regulation III, Rule 345, Vehicle and Mobile Equipment Coating
CA Antelope Valley Antelope Valley AVAQMD Rule 1151 (C)(3)(a)(iii)
CA Sacramento Sacramento Metropolitan Air Quality Management District Rule 459
CA San Joaquin San Joaquin Valley Air Pollution Control District Rule 4602 Section 5.6.4
CA Shasta County Shasta County Air Quality Management District Rule 3:25 section c.5.e
CA South Coast Air Quality Management District Rule 1151(d)(7)(A)(iii)
CO Colorado – entire state Colorado Air Quality Control Commission Regulation Nos. 3 and 7
IN Indiana – entire state Indiana Department of Environmental Management Rule 326 IAC 8-10

SUPERNOVA COMPLIANT WS400 EVOTECH

  • Complies with EPA NESHAP 40 CFR, Part 63 Subpart 6H
  • State-of-the-art automobile inspired design by Pininfarina
  • Patented LV Technology design combines a higher fluid delivery that
  • facilitates a faster, smoother application
  • Sprays in every climate condition with optimized atomization

See listings of WS400 APPROVED AREAS
Flyer
Parts / Specifications
Instruction Manual

The SUPERNOVA delivers a consistent droplet size when atomizing. This, combined with the flat, even SUPERNOVA pattern, helps reduce common application issues. All SUPERNOVA guns are equipped with stainless steel fluid passages ideal for any type of material, solventborne or waterborne.

The SUPERNOVA delivers a consistent droplet size when atomizing. This, combined with the flat, even SUPERNOVA pattern, helps reduce common application issues. All SUPERNOVA guns are equipped with stainless steel fluid passages ideal for any type of material, solventborne or waterborne.

 

W400-LV Spray Gun Approval

The ANEST IWATA W400-LV spray gun complies with regulations for application of coatings. See specifications on this page for a list of areas we serve.

These approvals are subject to conditions of the regional air quality agency. Information about these approvals are available below or call us at 1-800-470-7068 for details. You may also consult with the regional air quality agency in your jurisdiction.

US EPA Approval
W400LV EPA Compliant Letter PDF

Spray Guns Listing HVLP and Compliant Letter
AIUS EPA Letter PDF

W400 Compliant Spray Gun SCAQMD Letter
WS400 SCAQMD Letter PDF

NOTICE: It has been brought to our attention that some of ANEST IWATA spray guns sold via the internet may not be in compliance (non-compliant) with US environmental laws because they are not manufactured to be used in the US. We would like to remind customers of these laws, rules and approvals as set forth by the Environmental Protection Agency (EPA) and South Coast Air Quality Management District (SCAQMD), both of which requirements must be met to bring North American based ANEST IWATA spray guns into compliance. Read More…Non Compliant Internet Purchases 2016

 

United States of America Environmental Protection Agency (EPA) Environmental Technology Verification (ETV) ETV’s Verification Report
State General Jurisdiction Agency Complies with Rule/Regulation
CA Greater Los Angeles Metropolitan Area South Coast Air Quality Management District Rule 1151 (c)(4)(A)(iii)
CA Antelope Valley Antelope Valley AVAQMD Rule 1151 (C)(3)(a)(iii)
CA San Francisco / Oakland / San Jose Bay Area Quality Management District (BAAQMD) Regulation 8, Rule 45, Section 303.3
CA Butte County Butte County Air Quality Management District Rule 235 section 3.5.5
CA Kern County Kern County Air Pollution Control District Rules 410.4 & 410.4A
CA Mojave Desert Mojave Desert Air Quality Management District Rule 1116 (C)(2)(a)(iii)
CA Sacramento Sacramento Metropolitan Air Quality Management District Rule 459
CA San Luis Obispo San Luis Obispo Air Pollution Control District Rule 423
CA San Diego San Diego Air Pollution Control District Rule 67.20
CA San Joaquin San Joaquin Valley Air Pollution Control District Rule 4602 Section 5.6.4
CA Santa Barbara Santa Barbara County Air Pollution Control District Rule 339.D.7.f
CA Shasta County Shasta County Air Quality Management District Rule 3:25 section c.5.e
CA Ventura County Ventura County Air Pollution Control District Rule 74.18.B.4.e
CA Yolo – Solano Yolo – Solano Air Quality Management District Rule 2.26 Section 302.3
CO Colorado-entire state Colorado Air Quality Control Commission Regulation Nos. 3 and 7
MD Maryland – entire state Maryland Department of the Environment COMAR 26.11.19
NJ New Jersey – entire state New Jersey Department of Environmental Protection Rule 7:27-16.12 Non-HVLP Request Form
OR Oregon – entire state Oregon of Environmental Quality Rule 340-242-0620(2)(h)
PA Pennsylvania – entire state Pennsylvania Department of Environmental Protection 4 25 Pa. Code Section 129.75(e)(10)
TX Texas – entire state Texas Natural Resource Conservation Commission Rule 106.436(8) & 115.422(2)
OH Ohio – entire state Ohio Environmental Protection Agency Rule 3745-21-18
NY New York – entire state New York State Department of Environmental Conservation Rule 6 NYCRR 228.3 (f)(2)(vii)
IN Indiana – entire state Indiana Department of Environmental Management Rule 326 IAC 8-10
MA Massachusetts – entire state Commonwealth of Massachusetts Department of Environmental Protection Rule 310 CMR 7.03(16)(d)3
DE Delaware – entire state Department of Natural Resources & Environmental Control Regulation 24 Section 11(c)(1)(v)

W400-LV Compliant Spray Gun

April 7th, 2006

W400-LV Approval

W400-LV Compliant Spray Gun
ANEST IWATA USA, Inc. is pleased to announce the release of our W400-LV Compliant Spray Gun officially approved in specified locations and is subject to the conditions of the regional air quality agency.

The W400-LV spray gun sold and distributed within the jurisdiction of regional air quality district is subject to the local rule, including the following conditions:

ANEST IWATA AK-1B airflow control valve with air pressure gauge (Item #8130) shall be supplied with each W400-LV spray gun, and be properly attached to the spray gun and in good working condition

• Air inlet pressure supplied to the W400-LV spray gun shall be equal to or less than 20 psi.

Information about these approvals is available on our web site or call 1-800-440-0282 for details. You may also consult with the regional air quality agency in your jurisdiction.

Feel free to contact us with any questions that you might have.

Metallic Control – LPH400-LVB

August 15th, 2005

HVLP spray gun with our Super Basecoat Air Cap

Our LPH400-LVB combines the LPH400 with LV Technology and our Super Basecoat Air Cap to obtain improved control on refinish paints that contain fine metallic and pearls that standard set-ups face difficulties with such as mottling, blotching, streaking, floating, etc.

Find out more information inside the LPH400-LVB page.
CLICK HERE

Series 2 Spray Gun Approval

The ANEST IWATA Series 2 WS-400 spray gun complies with regulations for application of coatings. See specifications on this page for a list of areas we serve.

These approvals are subject to conditions of the regional air quality agency. Information about these approvals are available below or call us at 1-800-470-7068 for details. You may also consult with the regional air quality agency in your jurisdiction.

US EPA Approval
Series 2 WS-400 EPA Compliant Letter PDF

Series 2 WS-400 Compliant Spray Gun SCAQMD Letter
WS400 Series 2 DRAFT Approval Letter

WS-400 Compliance Letters
WS-400 Compliant AIUSNOTICE: It has been brought to our attention that some of ANEST IWATA spray guns sold via the internet may not be in compliance (non-compliant) with US environmental laws because they are not manufactured to be used in the US. We would like to remind customers of these laws, rules and approvals as set forth by the Environmental Protection Agency (EPA) and South Coast Air Quality Management District (SCAQMD), both of which requirements must be met to bring North American based ANEST IWATA spray guns into compliance. Read More…Non Compliant Internet Purchases 2016

 

United States of America Environmental Protection Agency (EPA) Environmental Technology Verification (ETV) ETV’s Verification Report
State General Jurisdiction Agency Complies with Rule/Regulation
AZ Arizona Maricopa Country Maricopa Country Air Pollution Control Regulation III, Rule 345, Vehicle and Mobile Equipment Coating
CA Antelope Valley Antelope Valley AVAQMD Rule 1151 (C)(3)(a)(iii)
CA Sacramento Sacramento Metropolitan Air Quality Management District Rule 459
CA San Joaquin San Joaquin Valley Air Pollution Control District Rule 4602 Section 5.6.4
CA Shasta County Shasta County Air Quality Management District Rule 3:25 section c.5.e
CA South Coast Air Quality Management District Rule 1151(d)(7)(A)(iii)
CO Colorado – entire state Colorado Air Quality Control Commission Regulation Nos. 3 and 7
IN Indiana – entire state Indiana Department of Environmental Management Rule 326 IAC 8-10

Test Product

  • Complies with EPA NESHAP 40 CFR, Part 63 Subpart 6H
  • State-of-the-art automobile inspired design by Pininfarina
  • Patented LV Technology design combines a higher fluid delivery that
    facilitates a faster, smoother application
  • Sprays in every climate condition with optimized atomization

 

 

See listings of WS400 APPROVED AREAS
Flyer
Parts / Specifications
Instruction Manual

 

The SUPERNOVA delivers a consistent droplet size when atomizing. This, combined with the flat, even SUPERNOVA pattern, helps reduce common application issues. All SUPERNOVA guns are equipped with stainless steel fluid passages ideal for any type of material, solventborne or waterborne.

The SUPERNOVA delivers a consistent droplet size when atomizing. This, combined with the flat, even SUPERNOVA pattern, helps reduce common application issues. All SUPERNOVA guns are equipped with stainless steel fluid passages ideal for any type of material, solventborne or waterborne.

 

HVLP and Compliant Spray Guns

March 12th, 2012

Spray Guns Listing HVLP and Compliant LETTER

ANEST IWATA USA, Inc. would like to confirm the following spray guns comply with EPA NESHAP 40 CFR, Part 63 Subpart HHHHHH HVLP and Compliant rule. The transfer efficiency of all listed guns is 65% per local air district mandates provided each particular gun is set-up by the user with the recommended inlet pressure and spray distances in each particular spray gun instruction manual. If you have discarded you instruction manual you download it from within our website.

Acronyms for ANEST IWATA spray guns:

LPH & LS is our acronyms for HVLP
W & WS is our acronyms for Conventional and Compliant

Qualifying Spray Guns:

LPHXXX HVLP manual guns:

LPH50, LPH80, LPH100 LVG, LPH101 LVG, LPH100 LVS, LPH101 LVS, LPH100 P, LPH101 P, LPH100 LVP, LPH200 P, LPH200 LVP, LPH300, LPH400 LV, LPH400 LVB, LPH400 LVX, LPH440, LS400, LS400H, AZ3HV2(AZ3HTE2 HVLP)

WXXX Compliant manual guns:

W400-LV

Since many customers have requested transfer efficiency data for our LPH400 and our W400LV spray gun’s, we are supplying a link to the EPA’s ETV program (Environmental Technology Verification Program) where this data can be downloaded.

Our EPA W400LV approval letter can be downloaded here: Compliant W400LV

Our Compliant W400LV testing report and statement can be downloaded here: Compliant W400LV

Our HVLP LPH400 testing report and statement can be downloaded here: HVLP LPH400

Once again, thanks to all who utilize and support ANEST IWATA products.

ANEST IWATA USA, Inc.

Waterborne Conversion

ANEST IWATA’s complete system for a seamless waterborne conversion is the W400-LV Compliant Spray Gun or the LPH400-LV HVLP Spray Gun combined with our ADG-1 Aquadry gun with stand will make you conversion and application of waterborne materials seamless. 

All ANEST IWATA Spray Guns have stainless steel fluid passages and are chrome plated for corrosion resistance, which makes for easy clean up.

Our Patented “LV Technology” allows for greater velocity needed to atomize waterborne materials and our ADG-1 “Aquadry” system is an indispensable item for waterborne flash acceleration. With a 6:1 air adjustment ratio and independently adjustable arms, the Dryer gun stand is perfect for any drying configuration.